Mustek PP3000 Manual de Instruções

TMRev.BPP3000 POS PRINTERMANUAL

1 - 1CHAP. 1GENER…TMGENERAL DESCRIPTIONOVERVIEWThe PP3000 series POS printer is a stream-lined low profile 40 column 9pin dot matrix printer designed

1 - 2TMCHAP. 1GENER…FEATURES• Dot matrix 9 pin printer head• Bi-directional printing• Friction type paper feed with optional sprocket paper feed• 40 c

2 - 1TMCHAP. 2INSTA…INSTALLATIONUNPACKING CONTENTS• The printer• Test ribbon cartridge• Roll paper shaft• Spacer for 3” paper roll (2 ea.)• Spacer for

2 - 2TMCHAP. 2INSTA…again. (ref. Fig. 2, the example uses parallel interface) Aim the rear hook to therectangular opening on the printer platform and

2 - 3TMCHAP. 2INSTA…For Other SystemInstall the printer on a stand or table which has a flat, even surface.Connect the power cord supplied for the pow

2 - 4TMCHAP. 2INSTA… Fig. 4 Cable connection examplesLOADING RIBBON CARTRIDGE• Turn the power for the printer off.• Squeeze the two side walls of the

2 - 5TMCHAP. 2INSTA…Fig. 5 Loading ribbon cartridgeFig. 6 Detail of ink ribbon at print headInk ribbonRibbonfeed knobRibboncartridgeRibbon cartridgein

2 - 6TMCHAP. 2INSTA…LOADING PAPER• Be sure to turn off the power for the printer.• Press the two sides of the top cover near the rear part a little bi

2 - 7TMCHAP. 2INSTA…(the thinner spacer for 3” and the thicker for 2.25” both with the flat sidefacing inward) and put the whole assembly onto the rol

TMWARRANTY AND EXCEPTIONSFederal Communications Commission Radio Frequency InterferenceStatementThis equipment has been tested and found to comply wit

2 - 8TMCHAP. 2INSTA… (3.0" SPACER)(2.25" SPACER) Fig. 8 Putting spacer to roll paper shaft Fig. 9 Finish paper loadingRemoving The Rol

3 - 1TMCHAP. 3OPERA…OPERATION GUIDEFRONT PANELThe positions of the below mentioned switches and LED’ s are indicatedin Fig. 10.“ON LINE” switchSwitche

3 - 2TMCHAP. 3OPERA…When all LEDs light up simultaneously and the buzzer soundscontinuously, a CPU error has occurred. In case of a CPU error, turn of

3 - 3TMCHAP. 3OPERA…continuously during self printing, only the characters will be printed outrepeatedly.A sample of the output of self print is given

3 - 4TMCHAP. 3OPERA…HEXADECIMAL DUMP MODE“ON LINE” + “POWER ON” (Turn the power on while holding the “ON LINE”switch depressed)Each of the signals sen

3 - 5TMCHAP. 3OPERA…Operation Method1. Open the top cover, pull the adjust lever one notch from standard positiontoward the operation panel side. When

3 - 6TMCHAP. 3OPERA…Printing FormatPrints one line in 7 x 9 font normal printing.32 columns (from the 5th to the 36th column)Even if the setting for p

3 - 7TMCHAP. 3OPERA…• Data received before a <GS> code is printed out when the printer receives the<GS> code.PERIPHERAL UNIT DRIVE CIRCUIT

3 - 8TMCHAP. 3OPERA…2. The status of the cash drawer open detection switch is interpreted as bit 7 ofthe printer status data (Refer to Data Structure

4 - 1TMCHAP. 4TECHN…TECHNICAL BACKGROUNDBLOCK DIAGRAMFig. 16 Circuit block diagramSerialinterfaceData(from host computer)DriverGate arrayCPUEPROM32KBR

TMCHAP. 1GENER…CHAP. 2INSTA…CHAP. 3OPERA…CHAP. 4TECHN…CHAP. 5MAIN …CHAP. 6MAINT…CHAP. 7CONTR…APP. ASTAR …APP. BFONT …APP. CQ & A …

4 - 2TMCHAP. 4TECHN…CIRCUITRY LAYOUT & CONNECTORSU1CN2CN178654321EDGONONEDG12345687ONEDG12345687ONEDG1234U5CN10CN9CN6CN4CN3U11SW1SW2SW3SW4CN5CN8CN

4 - 3TMCHAP. 4TECHN…has to be installed in U2 to use RS-422A interface. The details are described inthe table below.U3 U2 RS-232C Install MAX232A NOT

4 - 4TMCHAP. 4TECHN…U6&U8 : Font and BIOS socketThis socket is used to install BIOS and character font. Each type of printerrequires different BIO

4 - 5TMCHAP. 4TECHN…Data transmission rate ( baud rate ) bps 1-1 1-2 1-3 150 OFF OFF OFF 300 OFF OFF

4 - 6TMCHAP. 4TECHN…Character code table Switch U.S.A. & Europe IBM #1 IBM #2 Japan 2-7 ON ON OFF OFF 2-8 ON OFF ON

4 - 7TMCHAP. 4TECHN…a) When DIP SW4-1 through 4-4 are all ON (DC1/DC3 invalid mode)DC1 and DC3 codes are invalid.b) When DIP SW4-1 through 4-4 are OFF

4 - 8TMCHAP. 4TECHN…DIP-SW 2Switch Function ON OFF 2-1 2-2 International character set See table below 2-3 2-4 2-5 Not use

4 - 9TMCHAP. 4TECHN…DATA STRUCTURE IN SERIAL INTERFACEDTR ModeThis mode is accessed when the DIP switch 1-5 is ON. Signals arecontrolled using the DTR

4 - 10TMCHAP. 4TECHN…out”, load paper into the printer and press the “ON LINE” switch to set theprinter to “ON LINE”.Mechanical errorMechanical errors

4 - 11TMCHAP. 4TECHN…completely full). Output of the X-ON signal is resumed when the data in thebuffer is printed out and drops to below 256 bytes.Sta

4 - 12TMCHAP. 4TECHN…Framing errorA framing error occurs when “SPACE” is detected at the stop bit. When aframing error or a vertical parity error occu

4 - 13TMCHAP. 4TECHN…Sends ENQReceives statusbyteIs thedata bufferempty ?Sends STX signalIs itodd paritycheck?Set test byte FFHYESNOSet test byte 00HA

4 - 14TMCHAP. 4TECHN…

5 - 1TMCHAP. 5MAIN …MAIN SPECIFICATIONINTERFACEParallel Interface25 pin Female D-sub connectorPin#Signal Name I/O Function1 STROBE ISignals when data

5 - 2TMCHAP. 5MAIN …9 DATA 7 IThis signal provides the information of d7 the eighthbit (MSB) of parallel data. The signal is at HIGHlevel for a logica

5 - 3TMCHAP. 5MAIN …Serial Interface9 pin Female D-sub connectorPin#Signal Name I/O Function1 DCD O Data carrier detect2 TXD O Transmit data3 RXD I Re

5 - 4TMCHAP. 5MAIN …POWER SUPPLYPIN ASSIGNMENT OF 3 PIN JACK:PIN DEFINITION1 +24 V2 GND3 N.C.CASE CHASSIS GNDFig. 18 Pin layout of power plugHIMPORTAN

5 - 5TMCHAP. 5MAIN …The specifications for each character size are listed in the following table:Character size 15 CPI 12 CPI 8 CPIFont type 7 x 9 ha

5 - 6TMCHAP. 5MAIN …COMMANDSFriction type: 100% compatible to STAR SP312FVEPSON compatible model is option.Sprocket type: 100% compatible to STAR SP32

6 - 1TMCHAP. 6MAINT…MAINTENANCE CAUTION:Do not open the top cover and touch the print head immediately afterprinting, because the print head may be ve

iTMTable of ContentsGENERAL DESCRIPTION · · · · · · · · · · · · · · · · · · · 1 - 1OVERVIEW · · · · · · · · · · · · · · · · · · · · · · · · · · · ·1

6 - 2TMCHAP. 6MAINT… CAUTION:Remove the remaining paper in a forward direction. Do not pull itbackwards.• Clean the paper path when necessary.• Reload

7 - 1TMCHAP. 7CONTR…CONTROL CODESSTAR COMPATIBLE MODEControl Codes for Character SettingControl Codes Hex Codes FunctionESC R “n” <1B> <52>

7 - 2TMCHAP. 7CONTR…Control Codes for Line SpacingControl Codes Hex Codes FunctionLF <0A> Line feedCR <0D> Line feed (same as LF)ESC z 1

7 - 3TMCHAP. 7CONTR…Control Codes for Graphics PrintingControl Codes Hex Codes FunctionESC 1 <1B> <31> Set 7/72 inch line feedESC A “n” &l

7 - 4TMCHAP. 7CONTR…Control Codes for Peripheral UnitsControl Codes Hex Codes FunctionESC BEL “n1” “n2” <1B> <07> “n1”“n2”Adjust drive pu

7 - 5TMCHAP. 7CONTR…Reference Epson Models EmulatedEPSON TM-300 series.Character Size/Font MatricesRefer to page 5 - 4, the 8 CPI character size (5 x

7 - 6TMCHAP. 7CONTR…†These control codes are applicable in serial interface only.Control Codes Hex Codes FunctionHT <09> Horizontal tabLF <0A

A - 1TMAPP. ASTAR …APPENDIX ASTAR COMPATIBLE MODE COMMAND DETAIL(All commands are listed in hexadecimal code sequence)CODES (HEX/CONTROL) : 02 / <S

A - 2TMAPP. ASTAR …CODES (HEX/CONTROL) : 07 / <BEL>FUNCTION : Deferred drive command for peripheral unit 1DETAIL DESCRIPTION : Execute drive pul

A - 3TMAPP. ASTAR …CODES (HEX/CONTROL) : 0C / <FF>FUNCTION : Page feed (form feed)DETAIL DESCRIPTION : After data in the line buffer is printed

iiTMOPERATION METHOD · · · · · · · · · · · · · · · · · · · 3 - 5PRINTING FORMAT · · · · · · · · · · · · · · · · · · · · 3 - 6DATA FORMAT · · · ·

A - 4TMAPP. ASTAR …CODES (HEX/CONTROL) : 11 / <DC1> or 11 n / <DC1> nFUNCTION : Set select modeDETAIL DESCRIPTION :1. When using serial in

A - 5TMAPP. ASTAR …CODES (HEX/CONTROL) : 13 / <DC3>FUNCTION : Set deselect modeDETAIL DESCRIPTION :1. When using serial interface printer This f

A - 6TMAPP. ASTAR …CODES (HEX/CONTROL) : 19 / <EM>FUNCTION : Immediate drive command for peripheral unit 2APPLICATION LIMIT : Peripheral units 1

A - 7TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 25 01 / <ESC> “%” <1>FUNCTION : Enable download character setDETAIL DESCRIPTION : Enable the d

A - 8TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 26 00 n1 n2 / <ESC> “&” <0> n1 n2When 15 CPI character size is set (default setting), the

A - 9TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 2D 00 / <ESC> “-” <0>FUNCTION : Cancel underline modeDETAIL DESCRIPTION : The previously selec

A - 10TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 32 / <ESC> “2”FUNCTION : Set n/72 inch line feedDETAIL DESCRIPTION : This code sets the line feed a

A - 11TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 36 / <ESC> “6”FUNCTION : Select IBM character set #2APPLICATION LIMIT : This code is only valid whe

A - 12TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 41 n / <ESC> “A” nFUNCTION : Define n/72 inch line feedDEFINITION RANGE : 0 ≤ n ≤ 85 (Default n = 1

A - 13TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 44 n1…nk 0 / <ESC> “D” n1…nk <0>FUNCTION : Set horizontal tab positionDEFINITION RANGE : 1 ≤

iiiTMMAIN SPECIFICATION · · · · · · · · · · · · · · · · · · · · · 5 - 1INTERFACE · · · · · · · · · · · · · · · · · · · · · · · · · · · 5 - 1PARALLE

A - 14TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 4B n1 00 / <ESC> “K” n1 <0>1B H 4BH n1 00 m1 m2… / <ESC> “K” n1 <0> m1 m2…FUNCTIO

A - 15TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 4D / <ESC> “M”FUNCTION : Select 15 CPI character sizeAPPLICATION LIMIT : This code is valid only wh

A - 16TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 50 / <ESC> “P”FUNCTION : Select 12 CPI character sizeAPPLICATION LIMIT : This code is valid only wh

A - 17TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 55 00 / <ESC> “U” <0>FUNCTION : Select bi-directional print modeDETAIL DESCRIPTION : Returns

A - 18TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 57 30 / <ESC> “W” “0”FUNCTION : Cancel expanded character modeDETAIL DESCRIPTION : Cancel expanded

A - 19TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 61 n / <ESC> “a” nFUNCTION : Feed paper n linesDEFINITION RANGE : 1 ≤ n ≤ 127DETAIL DESCRIPTION : A

A - 20TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 68 31 / <ESC> “h” “1”FUNCTION : Select vertical expanded character modeAPPLICATION LIMIT :1. When c

A - 21TMAPP. ASTAR …CODES (HEX/CONTROL) : 1B 7A 00 / <ESC> “z” <0>FUNCTION : Set 1/12 inch line feedDETAIL DESCRIPTION : Line feed is set

A - 22TMAPP. ASTAR …CODES (HEX/CONTROL) : 1D data 0A / <GS> data <0A>FUNCTION : Select validation printingAPPLICATION LIMIT :1. Character

ivTMMAINTENANCE · · · · · · · · · · · · · · · · · · · · · · · · · · 6 - 1CLEANING · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6 - 1PAPER

vTMAPPENDIX ASTAR COMPATIBLE MODE COMMAND DETAIL · · A - 1APPENDIX BFONT TABLES · · · · · · · · · · · · · · · · · · · · · · · · · · B - 1U.S.A. &a