Mustek PP4000 Series Guia do Utilizador

Rev.: OriginalPP4000 SeriesThermal PrinterUser's Guide

1 - 6F. INDICATORS• POWER LED: green• PAPER END INDICATOR: red. Different lightingpattern indicates each error status.Lighting pattern MeaningConstant

1 - 7G. OPERATING ENVIRONMENT• Place the printer on a sturdy, level surface.• Choose a place that is well ventilated and free ofexcessive dust, smoke

1 - 8H. USEFUL TIPS• Do not pull the paper in the direction opposite to thepaper feeding direction with the print head closed.• Do not touch the areas

1 - 9• Store thermal paper away from high temperature andhumidity. Avoid extended exposure to direct light.• Do not set any liquid or drinks such as c

2 - 1II. QUICK START-UPA. LOADING PAPER Open top cover by gently pressing the rear part of coverinward and lift it up. Take the cover away to expose t

2 - 2thermal print engine and try to aim the front end of the paper rolltoward the rear insert slot. When the front end is inserted into the rear inse

2 - 3 2. Manual paper feedYou may also extend the front end of paper out of the paperexit slot of the top cover and put top cover back to the printer

2 - 4B. CONNECTING CABLES1. SERIAL CONNECTIONAll the external connectors are in the recessed area at therear bottom. The serial connector is a 9 pin D

2 - 52. PARALLEL CONNECTIONThe parallel connector is a 25 pin D sub Male connector atthe rightmost location in the connector area. Apply this cable on

2 - 64. POWER CONNECTION The power connector is a 3 pin jack between the peripheralconnector and the parallel connector. During insertion, be sure toh

Federal Communications Commission Radio FrequencyInterference StatementThis equipment has been tested and found to comply with the limits for a Class

2 - 76. SELF TESTPress and hold down the paper feed button while turning theon / off switch on. The printer will then perform a self test. A slipof se

2 - 8

3 - 1III. MAINTENANCE AND INTERNALPARTSA. MAINTENANCE GUIDE LINES• Always turn off and disconnect power before openingthe cover.• The areas around the

3 - 2C. PAPER JAMIn case of paper jam, please open the top cover and pushdown the auto cutter assembly so that it could be easier to get themessed up

3 - 3 Head-up lever at up position Head-up lever at normal down positionPush head-up lever further down Freeing the movement of the guide platePull

3 - 4 Guide slot of print headGently move the print head along its guide slot out (do notdamage the cabling to it and never do this when print head is

4 - 1IV. SPECIFICATIONSA. PRINTERITEM SPECIFICATIONPrinting method Thermal sensitive line dot methodEffective printing width 72 mmThermal headconfigur

4 - 2C. POWER ADAPTORITEM REQUIREMENTINPUT VOLTAGE 100 V AC ~ 250 V ACINPUT FREQUENCY 50 ~ 60 HZINPUT CURRENT 1.5 A MAX.OUTPUT VOLTAGE + 24 V DCOUTPUT

5 - 1V. TECHNICAL INFORMATIONA. INTERFACES1. SERIAL INTERFACEa.RS232The standard serial interface applicable to PP4000S isRS232. The communication pro

5 - 22. PARALLEL INTERFACEThe communication interface applied in PP4000C is theCentronics parallel interface using a 25 pin D sub male connectorwith t

iTable Of ContentsGETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1CONGRATULATION . . . . . . . . . . . . . . . . . . . . . 1 -- 1PRODU

5 - 3 PIN # Definition Description1 FG Frame ground2 CRBDrawer kick for cash drawer controlled bysoftware command Esc p 0 n1 n23 SENSE Input periphe

5 - 4When the bottom metal plate is removed by a qualifiedtechnician, you can see the control board from the bottom asshown in the above picture. Plea

5 - 5C. SOFTWARE COMMANDSCodes (HEX / CONTROL) : COMMAND NAME(1) 09 / <HT> : Horizontal tab(2) 0A / <LF> : Line feed with printing(3) 0C /

5 - 6(17) 1B 44 [d]k 00 / <ESC> “D” [d]k <NUL> : Horizontal tabposition setting(18) 1B 4A n / <ESC> “J” n : Printing and minimum - p

5 - 7(39) 1D 26 m x y1 y2 [d]k / <GS> “&” m x y1 y2 [d]k : Registrationof image data(40) 1D 27 m n / <GS> “’ ” m n : Print registered

6 - 1VI. CHARACTER CODE PAGESA. PAGE 0 ENGLISH / JAPANESE

6 - 2B. PAGE 1 ENGLISH / EUROPEAN(In these tables, “SP” indicates a space.)Note:1. Each code is represented in hexadecimal notation.2. If an undefined

6 - 3data, character registration data, or command parameters arereceived, they are handled as ordinary data.)

iiPOWER ADAPTOR . . . . . . . . . . . . . . . . . . . . . . . 4 -- 2TECHNICAL INFORMATION . . . . . . . . . . . . . . . 5 -- 1INTERFACES . . . . . .

1 - 1I. GETTING STARTEDA. CONGRATULATIONYou have made a very wise decision by purchasing the highspeed – low noise –high resolution – light weight – h

1 - 2B. PRODUCT BRIEFINGThe PP4000 series printer uses thermal sensitive paper inform of a roll at a width of 80 mm. The PP4000 printer serves thestan

1 - 3C. MODEL NUMBERSEXAMPLE: PP 4 0 0 0 S 0Power adaptor:0: No adaptor1: USA adaptor2: European adaptor3: UK adaptor4: SA adaptor5: AUS adaptorInterf

1 - 4D. UNPACKING As illustrated in the above picture, followings are items youmay find when you carefully unpack the carton that deliversPP4000 serie

1 - 5E. MAIN PARTS ON THE EXTERIORPower LED (green)Paper End LED (red)Paper feed buttonPower On / off switchPaper exit slotBottom baseTop cover